£298.80 (incl. VAT)
-
Rako RAK8-MB Modular Dimming / Control Rack
£558.00The RAKO RAK8-MB is a 8 Channel modular dimming rack motherboard. It has 8 individual channel “slots” that allow complete flexibility of controlled loads when fitted with either of the WMT-400, WDA-600, WMS600 or WM-CUB control cards (these are an additional purchase) The RAK8 unit is stackable with other RAK8 units. It requires a RAK-LINK for wired systems or RX-LINK for wireless controlled systems.
-
Rako RAKLink
£520.80The RAK-LINK provides an isolated link between the RAK4 dimmer units and wired RAKOM products. The unit also includes a heavy duty 15v dc power supply for the RAKOM network. Connection for the CAT5 is by 8 way punch down terminals. This allows for a daisy chain configuration of the RAKOM wired network. Where a ‘star’ or ‘home-run’ configurations are required the use of the RAK-STAR unit is needed. Three RJ11 programming sockets within the unit allows system programming using the RASOFT software suite and connection of other RAKOM accessories such as the WA-BRIDGE interface.
-
Rako RAKStar
£432.00The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
-
Rako RxLink Wireless RAK Interface Module
£298.80Rako RxLink Wireless RAK Interface Module is designed to be the gateway between Rako transmitter devices and the RAK-4 range of dimmer racks allowing the dimmer racks to be mounted remotely to the lighting loads, RF push button wall plates and other Rako RF accessories. Creates the link for combined Wired & Wireless systems.
-
Rako WAVFR Wired Volt Free Interface
£279.60The Rako WAVFR is a compact interface unit for use with the Rako Rakom wired network. The WAVFR allows up to 10 volt-free contact closures to interface to the network which can then trigger lighting scenes and actions. It is fitted with a 10 way set of screw terminals for signal input and an additional 3 way connector for Common inputs.
The WAVFR is configured in Rasoft and signal inputs can trigger lighting scenes or actions in a similar fashion to button presses on a wall panel. -
Rako WAVMI Wired Mains Input Interface
£279.60Rako WAVMI Wired Mains Input Interface is a compact interface unit for use with the Rako Rakom wired network. The WAVMI allows up to 5 mains voltage switching devices to interface to the network which can then trigger lighting scenes.
The WAVMI is suited for interfacing with a mains indoor or outdoor PIR sensor. It is requires connection to and is powered from a RAK-LINK or RAK-STAR unit.
-
Rako WDA-600 control card dimmer – 0-10v, DSI & DALI lighting
£141.60The Rako WDA-600 is a universal control card dimmer for 0-10v, DSI & DALI broadcast lighting loads. It has a 600W maximum loading and is designed to be used with the RAK8-MB 8 channel modular dimming rack motherboard.
-
Rako WLED150CV1 wired 150w constant voltage dimming LED driver
£298.80The Rako WLED150CV1 wired 150w constant voltage dimming LED driver is designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 150W for 12V d.c. fittings or 300w for 24V d.c. fittings
-
Rako WLED75CV1 wired 75w constant voltage dimming LED driver
£207.60The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
-
Rako WMCUB Twin Relay Curtain & Blind Control Card
£141.60The Rako WM-CUB is a Twin Relay curtain and blind control card which forms part of the new RAK8 modular system. The new RAK8 modular system allows you to add individual control cards to your RAK8-MB (modular board) with complete flexibility to build a bespoke system to meet your requirements. The WM-CUB is used for implementation of control, for motorised curtains, screens and blinds. Delivering an open, close and stop functionality.
-
Rako WML-300 leading edge pluggable module
£141.60The Rako WML-300 is a 300W leading edge pluggable module for use with RAK8-MB that is suitable for dimming tungsten, low voltage halogens and other leading edge dimmable loads.
-
Rako WMS-600 Switching 600W RAK8 control card module
£123.60The Rako WMS-600 is new to the Rako range of programmable lighting control. The new WMS-600 is a 600W pluggable module for use with RAK8-MB, that is suitable for use with non dimmable loads or other outputs that require mains switching.
The Rako WMS-600 is plugged directly into the RAK8-MB board and is best suited for use with non dimmable lighting loads, extractor fans or any other switched mains output applications.
-
Rako WMT-400 Trailing edge 400W RAK8 control card dimmer
£141.60The Rako WMT-400 is a pluggable trailing edge dimmer module to be used with the RAK8-MB. The Rako WMT-400 unit is plugged directly into one of the slots on the RAK8- MB.
The WMT-400 can be used in combination with any of the other modules compatible with the RAK8 allowing for greater flexibility during both specification and installation. Trailing edge dimming technology gives smooth quiet dimming of electronic transformer fed loads and maximises dimming performance of most GU10 and other LED fittings.
-
Rako WP-CON Single Gang Wired Connection Plate
£68.40The Rako WPCON and Rako WPCON-C units provide convenient connection points to the Rakom wired network for devices such as DMX, RF, WA and WTC Bridge modules. They provide a permanent punch down connection to the Rakom network and an RJ11 socket for plug in connection of the devices.
-
Rako WSR-DMX Wired-System 15 Channel DMX Control Module
£301.20The Rako WSR-DMX is a 15 channel DMX controller for use with the Rako Rakom wired network. It can be used to control DMX light fittings or interfaces such as colour changing LED drivers and fibre optic projectors.
