The Rako RMR-VF is an interface unit to convert volt-free contact signals into Rako wireless RAKOM messages. This unit creates an interface between volt-free contact or DC logic inputs and Rako RF based receivers. The unit accepts up to 10 contact closures which can be mapped using RASOFT Pro to mimic keypad presses.
Rako’s RMR-VF wireless system interface will accommodate up to 10 volt free contact closure inputs and is supplied complete with a power supply.
For contact interfacing the RMR-VF accepts up to 10 volt-free inputs which can be used to trigger multiple scenes within a single room or separate commands in different rooms. Commands can be scenes, fades, levels or multiple actions depending on the duration of the contact closure.
The unit can be addressed manually for a single room application, the inputs will trigger basic scenes within that room. If you require control in multiple rooms the RMR-VF unit will require programming using the Rasoft Pro is (with a suitable programming interface e.g. RABridge) to map commands to different or multiple rooms and action advanced functions such as Level, Press and Hold and Trigger on Release.
NB: The RMR-VF is not intended for use with PIR or other presence sensors. For these sensors the RAMVR should be used.
Accepts up to 10 volt-free inputs
Advanced programming commands include fades, levels or multiple actions (dependent upon duration of contact closure)
Can be addressed manually to a single Rako Room and inputs will trigger basic scenes within that Room
Can be programmed using Rasoft for multi-room application
9-12V DC from SELV power supply unit (included)
UL V0 ABS
Temperature +2C to +40C
Humidity +5% to 95% non condensing
Emissions – EN61000-6-3 : 2007
Immunity – EN61000-6-1 : 2007 LVD – EN 60950-1 :2006
Rak4R is a 4 Channel twin relay control unit for control of up to 4 curtain or blind motors. Configurable to suit most motor types such as 240V roller, Venetian or Roman blinds, curtain tracks or low voltage motors. Relays are isolated and can be used to provide volt-free contact closures from the Rako network for nonmotor control applications.
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The Rako WMT-400 is a pluggable trailing edge dimmer module to be used with the RAK8-MB. The Rako WMT-400 unit is plugged directly into one of the slots on the RAK8- MB.
The WMT-400 can be used in combination with any of the other modules compatible with the RAK8 allowing for greater flexibility during both specification and installation. Trailing edge dimming technology gives smooth quiet dimming of electronic transformer fed loads and maximises dimming performance of most GU10 and other LED fittings.
The RNC wireless push button wall plate controller with 4 scenes, off and master raise and lower buttons. Customisable and programmable via NFC (Near Field Communication).
The RNC-100, 10 button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
A compact 800VA RF dimmer for 1-10V, DALI and DSI controllable loads. Connected in-line before the first lighting fitting the RMS800 enables switching of up to 800VA of 0-10V, DALI and DSI controllable loads such as LED drivers and dimmable fluorescent ballasts. Controlled from any Rako Rakom RF device, for example the RCP/RCM push button RF wall-plates.
The RAKO RAK8-MB is a 8 Channel modular dimming rack motherboard. It has 8 individual channel “slots” that allow complete flexibility of controlled loads when fitted with either of the WMT-400, WDA-600, WMS600 or WM-CUB control cards (these are an additional purchase) The RAK8 unit is stackable with other RAK8 units. It requires a RAK-LINK for wired systems or RX-LINK for wireless controlled systems.
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
A four channel dimming rack, designed to be wall mounted in an electrical cupboard. Incorporating the latest dimming technology. Each of the four channels can independantly control 0-10v, DSI or DALI dimmable lighting load or switched circuits. The dimmer has four seperate dimming channels that can control a total of 2400w of lighting.
The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
Thank you for your custom. We aim to dispatch your goods as soon as possible via our courier APC. All deliveries will require a signature unless otherwise specifically requested when placing your order. Dismiss