Product Description
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
£211.20 (incl. VAT)
£262.80 (Inc. VAT)
£219.00 (Exc. VAT)
In Stock
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The RAKO RAK8-MB is a 8 Channel modular dimming rack motherboard. It has 8 individual channel “slots” that allow complete flexibility of controlled loads when fitted with either of the WMT-400, WDA-600, WMS600 or WM-CUB control cards (these are an additional purchase) The RAK8 unit is stackable with other RAK8 units. It requires a RAK-LINK for wired systems or RX-LINK for wireless controlled systems.
The Rako WMT-400 is a pluggable trailing edge dimmer module to be used with the RAK8-MB. The Rako WMT-400 unit is plugged directly into one of the slots on the RAK8- MB.
The WMT-400 can be used in combination with any of the other modules compatible with the RAK8 allowing for greater flexibility during both specification and installation. Trailing edge dimming technology gives smooth quiet dimming of electronic transformer fed loads and maximises dimming performance of most GU10 and other LED fittings.
The Rako WSR-DMX is a 15 channel DMX controller for use with the Rako Rakom wired network. It can be used to control DMX light fittings or interfaces such as colour changing LED drivers and fibre optic projectors.
The Rako WM-CUB is a Twin Relay curtain and blind control card which forms part of the new RAK8 modular system. The new RAK8 modular system allows you to add individual control cards to your RAK8-MB (modular board) with complete flexibility to build a bespoke system to meet your requirements. The WM-CUB is used for implementation of control, for motorised curtains, screens and blinds. Delivering an open, close and stop functionality.
The Rako RMS-800 switching module can control up to 800 watts of mains non dimmable lighting loads. The unit can also be used for exterior lighting control applications, with the use of a weatherproof IP rated enclosure. The robust microprocessor design combines reliable switching with dynamic safety features such as auto-resetting over current and voltage surge protection. The RMS-800 switch module can be controlled from any Rako transmitter such as RCP/RCM wallplates, RAH hand helds, MB1 timeclocks and forms the foundation of any Rako scene-set system
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
A compact 800VA RF dimmer for 1-10V, DALI and DSI controllable loads. Connected in-line before the first lighting fitting the RMS800 enables switching of up to 800VA of 0-10V, DALI and DSI controllable loads such as LED drivers and dimmable fluorescent ballasts. Controlled from any Rako Rakom RF device, for example the RCP/RCM push button RF wall-plates.
The Rako RMR-VF is an interface unit to convert volt-free contact signals into Rako wireless RAKOM messages. This unit creates an interface between volt-free contact or DC logic inputs and Rako RF based receivers. The unit accepts up to 10 contact closures which can be mapped using RASOFT Pro to mimic keypad presses.
The RAKO WK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wired commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cutout is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako RCM-020 Wireless keypad module is compatible with the RLF and RVF series coverplates. It is a wireless 2 button control module that arrives pre configured for a scene 1 on, and off option. As the unit is wireless it can be mounted anywhere on a rigid surface you will need the coverplate kit for mounting. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
The RCM100 push button control module comes pre-configured for selecting 7 scenes, off and master raise & lower. The wall plate controllers are designed to be mounted anywhere, be it flush mounting to UK back-boxes or simply surface mounted to any flat surface using the pattress provided. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
CyberSelect now offer a Rako Pre-Programming Service for Rako Lighting Control modules purchased from CyberSelect.
We have an experienced installation team, who complete installs every week. These installations range from larger complex lighting systems, integrated lighting within a Smart Home, to small and simple Rako Lighting Control both Wired Systems and Wireless Systems working seamlessly together. They can assist with pre-programming of your modules for your Rako Lighting Control and Home Automation System.