Product Description
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
£11,954.92 (incl. VAT)
£262.80 (Inc. VAT)
£219.00 (Exc. VAT)
In Stock
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The RAKO RAK8-MB is a 8 Channel modular dimming rack motherboard. It has 8 individual channel “slots” that allow complete flexibility of controlled loads when fitted with either of the WMT-400, WDA-600, WMS600 or WM-CUB control cards (these are an additional purchase) The RAK8 unit is stackable with other RAK8 units. It requires a RAK-LINK for wired systems or RX-LINK for wireless controlled systems.
The RNC wireless push button wall plate controller with 4 scenes, off and master raise and lower buttons. Customisable and programmable via NFC (Near Field Communication).
The RNC-100, 10 button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
The Rako RMR-VFÂ is an interface unit to convert volt-free contact signals into Rako wireless RAKOM messages. This unit creates an interface between volt-free contact or DC logic inputs and Rako RF based receivers. The unit accepts up to 10 contact closures which can be mapped using RASOFT Pro to mimic keypad presses.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The Rako RLF-020, Mirrored Stainless Steel, 2 button Screwless Cover Plate Kit, is suitable for Wireless Rako RNC-020 and RCM-020 Keypad Modules only.
Keypads are sold available separately
The RNC push button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
The Rako WMT-400Â is a pluggable trailing edge dimmer module to be used with the RAK8-MB. The Rako WMT-400 unit is plugged directly into one of the slots on the RAK8- MB.
The WMT-400 can be used in combination with any of the other modules compatible with the RAK8 allowing for greater flexibility during both specification and installation. Trailing edge dimming technology gives smooth quiet dimming of electronic transformer fed loads and maximises dimming performance of most GU10 and other LED fittings.
The RAKO WK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wired commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cutout is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
Rako WP-EOS-6 in Polished Chrome 6-Button wired EOSÂ wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.