Product Description
The Rako WVF-070 series, Polished Brass 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
£273.60 (incl. VAT)
£42.00 (Inc. VAT)
£35.00 (Exc. VAT)
In Stock
The Rako WVF-070 series, Polished Brass 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-070 series, Polished Brass 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
The Rako RACUB is a compact dual relay RF switching module. Ideal for integrating motorised curtains, blinds and projector screens with the lighting control system. Controlled from any Rako Rakom RF device, for example the RPS030 /060 or RCM030 / 060 three or six button RF wall plates.
The Rako RK-MOD is a Wireless Modular wall plate controller that is available in nine preconfigured button layouts. The wireless Modular control module is programmable via Rako’s patented NFC (Near Field Communication) technology, allowing each button to trigger a single or multiple commands. This product can only be programmed with a laptop using Rako’s Rasoft Pro software and a HUB or RAMPI programming interface.
The Rako RSR-DALI is a wireless receiver module with outputs to control 15 channels of addressable DALI fittings in a single Rako Room.
The Rako RLF-020, Black Nickel, 2 button Screwless Cover Plate Kit, is suitable for Wireless Rako RNC-020 and RCM-020 Keypad Modules only.
Keypads are sold available separately
The RNC push button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The Rako RMR-VF is an interface unit to convert volt-free contact signals into Rako wireless RAKOM messages. This unit creates an interface between volt-free contact or DC logic inputs and Rako RF based receivers. The unit accepts up to 10 contact closures which can be mapped using RASOFT Pro to mimic keypad presses.
The RAKO RAK8-MB is a 8 Channel modular dimming rack motherboard. It has 8 individual channel “slots” that allow complete flexibility of controlled loads when fitted with either of the WMT-400, WDA-600, WMS600 or WM-CUB control cards (these are an additional purchase) The RAK8 unit is stackable with other RAK8 units. It requires a RAK-LINK for wired systems or RX-LINK for wireless controlled systems.
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
Rako WP-EOS-6 in Satin Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
The RAKO RK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wireless commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cut out is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.