Product Description
The Rako WVF-070 series, Polished Brass 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
£193.20 (incl. VAT)
£42.00 (Inc. VAT)
£35.00 (Exc. VAT)
In Stock
The Rako WVF-070 series, Polished Brass 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-070 series, Polished Brass 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The Rako RCM-020 Wireless keypad module is compatible with the RLF and RVF series coverplates. It is a wireless 2 button control module that arrives pre configured for a scene 1 on, and off option. As the unit is wireless it can be mounted anywhere on a rigid surface you will need the coverplate kit for mounting. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
The RNC push button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
Rako WP-EOS-6 in Satin Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
The Rako RACUB is a compact dual relay RF switching module. Ideal for integrating motorised curtains, blinds and projector screens with the lighting control system. Controlled from any Rako Rakom RF device, for example the RPS030 /060 or RCM030 / 060 three or six button RF wall plates.
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The Rako RLF-020, Black Nickel, 2 button Screwless Cover Plate Kit, is suitable for Wireless Rako RNC-020 and RCM-020 Keypad Modules only.
Keypads are sold available separately
The Rako RAMPI USB Programming Interface is designed to operate with the Rako Rasoft Pro programming software the RAMPI allows easy programming of a wireless Rako system. The RAMPI also supports NFC (Near Field Communication) programming of Rako’s NFC devices such as the RNC control panels and RCI interface modules.
The Rako WSR-DMX is a 15 channel DMX controller for use with the Rako Rakom wired network. It can be used to control DMX light fittings or interfaces such as colour changing LED drivers and fibre optic projectors.