Product Description
The Rako WVF-070 series, White Metal, 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
£175.20 (incl. VAT)
£32.40 (Inc. VAT)
£27.00 (Exc. VAT)
In Stock
The Rako WVF-070 series, White Metal, 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-070 series, White Metal, 7 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-070 Keypad Modules only.
Keypads are sold available separately
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
The Rako RACUB is a compact dual relay RF switching module. Ideal for integrating motorised curtains, blinds and projector screens with the lighting control system. Controlled from any Rako Rakom RF device, for example the RPS030 /060 or RCM030 / 060 three or six button RF wall plates.
The RAKO RK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wireless commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cut out is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
A compact 800VA RF dimmer for 1-10V, DALI and DSI controllable loads. Connected in-line before the first lighting fitting the RMS800 enables switching of up to 800VA of 0-10V, DALI and DSI controllable loads such as LED drivers and dimmable fluorescent ballasts. Controlled from any Rako Rakom RF device, for example the RCP/RCM push button RF wall-plates.
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The Rako RK-MOD is a Wireless Modular wall plate controller that is available in nine preconfigured button layouts. The wireless Modular control module is programmable via Rako’s patented NFC (Near Field Communication) technology, allowing each button to trigger a single or multiple commands. This product can only be programmed with a laptop using Rako’s Rasoft Pro software and a HUB or RAMPI programming interface.
The RNC wireless push button wall plate controller with 4 scenes, off and master raise and lower buttons. Customisable and programmable via NFC (Near Field Communication).
The RNC-100, 10 button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
Rako WP-EOS-6 in Satin Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.
The Rako WSR-DMX is a 15 channel DMX controller for use with the Rako Rakom wired network. It can be used to control DMX light fittings or interfaces such as colour changing LED drivers and fibre optic projectors.