Product Description
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
£193.20 (incl. VAT)
£32.40 (Inc. VAT)
£27.00 (Exc. VAT)
In Stock
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The Rako RSR-DALI is a wireless receiver module with outputs to control 15 channels of addressable DALI fittings in a single Rako Room.
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
The Rako WMT-400 is a pluggable trailing edge dimmer module to be used with the RAK8-MB. The Rako WMT-400 unit is plugged directly into one of the slots on the RAK8- MB.
The WMT-400 can be used in combination with any of the other modules compatible with the RAK8 allowing for greater flexibility during both specification and installation. Trailing edge dimming technology gives smooth quiet dimming of electronic transformer fed loads and maximises dimming performance of most GU10 and other LED fittings.
The RAK-LINK provides an isolated link between the RAK4 dimmer units and wired RAKOM products. The unit also includes a heavy duty 15v dc power supply for the RAKOM network. Connection for the CAT5 is by 8 way punch down terminals. This allows for a daisy chain configuration of the RAKOM wired network. Where a ‘star’ or ‘home-run’ configurations are required the use of the RAK-STAR unit is needed. Three RJ11 programming sockets within the unit allows system programming using the RASOFT software suite and connection of other RAKOM accessories such as the WA-BRIDGE interface.
The Rako RMR-VF is an interface unit to convert volt-free contact signals into Rako wireless RAKOM messages. This unit creates an interface between volt-free contact or DC logic inputs and Rako RF based receivers. The unit accepts up to 10 contact closures which can be mapped using RASOFT Pro to mimic keypad presses.
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The RAKO WK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wired commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cutout is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako WSR-DMX is a 15 channel DMX controller for use with the Rako Rakom wired network. It can be used to control DMX light fittings or interfaces such as colour changing LED drivers and fibre optic projectors.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
Rako WP-EOS-6 in Polished Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.
The RAKO RK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wireless commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cut out is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako RMS-800 switching module can control up to 800 watts of mains non dimmable lighting loads. The unit can also be used for exterior lighting control applications, with the use of a weatherproof IP rated enclosure. The robust microprocessor design combines reliable switching with dynamic safety features such as auto-resetting over current and voltage surge protection. The RMS-800 switch module can be controlled from any Rako transmitter such as RCP/RCM wallplates, RAH hand helds, MB1 timeclocks and forms the foundation of any Rako scene-set system