Product Description
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
£5,230.72 (incl. VAT)
£262.80 (Inc. VAT)
£219.00 (Exc. VAT)
In Stock
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako WM-CUB is a Twin Relay curtain and blind control card which forms part of the new RAK8 modular system. The new RAK8 modular system allows you to add individual control cards to your RAK8-MB (modular board) with complete flexibility to build a bespoke system to meet your requirements. The WM-CUB is used for implementation of control, for motorised curtains, screens and blinds. Delivering an open, close and stop functionality.
A compact 800VA RF dimmer for 1-10V, DALI and DSI controllable loads. Connected in-line before the first lighting fitting the RMS800 enables switching of up to 800VA of 0-10V, DALI and DSI controllable loads such as LED drivers and dimmable fluorescent ballasts. Controlled from any Rako Rakom RF device, for example the RCP/RCM push button RF wall-plates.
The RAK-LINK provides an isolated link between the RAK4 dimmer units and wired RAKOM products. The unit also includes a heavy duty 15v dc power supply for the RAKOM network. Connection for the CAT5 is by 8 way punch down terminals. This allows for a daisy chain configuration of the RAKOM wired network. Where a ‘star’ or ‘home-run’ configurations are required the use of the RAK-STAR unit is needed. Three RJ11 programming sockets within the unit allows system programming using the RASOFT software suite and connection of other RAKOM accessories such as the WA-BRIDGE interface.
The RAKO WK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wired commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cutout is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
The RCM100 push button control module comes pre-configured for selecting 7 scenes, off and master raise & lower. The wall plate controllers are designed to be mounted anywhere, be it flush mounting to UK back-boxes or simply surface mounted to any flat surface using the pattress provided. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
The Rako RAMPI USB Programming Interface is designed to operate with the Rako Rasoft Pro programming software the RAMPI allows easy programming of a wireless Rako system. The RAMPI also supports NFC (Near Field Communication) programming of Rako’s NFC devices such as the RNC control panels and RCI interface modules.
The Rako RMT-PILL is designed to offer flexible control and fits in to a standard UK or European back-box. A compact 250W RF dimmer designed to be located in a standard UK or European backbox. The RMT-Pill can be used either with or without a neutral allowing it to be used with dedicated wiring or retrofit into a standard wiring situation. Trailing edge technology for quiet reliable dimming of any non-inductive load when used with a neutral or tungsten GLS and tungsten halogen GU10 style lamps when used without. Controlled from any Rako Rakom device or simple contact closure input using a momentary push switch.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The Rako RK-MOD is a Wireless Modular wall plate controller that is available in nine preconfigured button layouts. The wireless Modular control module is programmable via Rako’s patented NFC (Near Field Communication) technology, allowing each button to trigger a single or multiple commands. This product can only be programmed with a laptop using Rako’s Rasoft Pro software and a HUB or RAMPI programming interface.
The Rako RMR-VF is an interface unit to convert volt-free contact signals into Rako wireless RAKOM messages. This unit creates an interface between volt-free contact or DC logic inputs and Rako RF based receivers. The unit accepts up to 10 contact closures which can be mapped using RASOFT Pro to mimic keypad presses.