Product Description
The Rako WLF-020, Black Nickel, 2 Button Screwless Cover Plate Kit, is suitable for Wired Rako WCM-020 Keypad Modules only.
Keypads are sold available separately
£61.20 (Inc. VAT)
£51.00 (Exc. VAT)
In Stock
The Rako WLF-020, Black Nickel, 2 Button Screwless Cover Plate Kit, is suitable for Wired Rako WCM-020 Keypad Modules only.
Keypads are sold available separately
The Rako WLF-020, Black Nickel, 2 Button Screwless Cover Plate Kit, is suitable for Wired Rako WCM-020 Keypad Modules only.
Keypads are sold available separately
The Rako RACUB is a compact dual relay RF switching module. Ideal for integrating motorised curtains, blinds and projector screens with the lighting control system. Controlled from any Rako Rakom RF device, for example the RPS030 /060 or RCM030 / 060 three or six button RF wall plates.
A compact 800VA RF dimmer for 1-10V, DALI and DSI controllable loads. Connected in-line before the first lighting fitting the RMS800 enables switching of up to 800VA of 0-10V, DALI and DSI controllable loads such as LED drivers and dimmable fluorescent ballasts. Controlled from any Rako Rakom RF device, for example the RCP/RCM push button RF wall-plates.
The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
The RAKO RK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wireless commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cut out is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The RCM100 push button control module comes pre-configured for selecting 7 scenes, off and master raise & lower. The wall plate controllers are designed to be mounted anywhere, be it flush mounting to UK back-boxes or simply surface mounted to any flat surface using the pattress provided. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The RCM070 push button control module comes pre-configured for selecting 4 scenes, off and master raise & lower. The wall plate controllers are designed to be mounted anywhere, be it flush mounting to UK back-boxes or simply surface mounted to any flat surface using the pattress provided. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement
The Rako WSR-DMX is a 15 channel DMX controller for use with the Rako Rakom wired network. It can be used to control DMX light fittings or interfaces such as colour changing LED drivers and fibre optic projectors.
The Rako RAMPI USB Programming Interface is designed to operate with the Rako Rasoft Pro programming software the RAMPI allows easy programming of a wireless Rako system. The RAMPI also supports NFC (Near Field Communication) programming of Rako’s NFC devices such as the RNC control panels and RCI interface modules.
CyberSelect now offer a Rako Pre-Programming Service for Rako Lighting Control modules purchased from CyberSelect.
We have an experienced installation team, who complete installs every week. These installations range from larger complex lighting systems, integrated lighting within a Smart Home, to small and simple Rako Lighting Control both Wired Systems and Wireless Systems working seamlessly together. They can assist with pre-programming of your modules for your Rako Lighting Control and Home Automation System.