Product Description
The Rako WVF-020-SS, Brushed Stainless Steel, 2 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-020 Keypad Modules only.
Keypads are sold available separately
£32.40 (Inc. VAT)
£27.00 (Exc. VAT)
In Stock
The Rako WVF-020-SS, Brushed Stainless Steel, 2 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-020 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-020-SS, Brushed Stainless Steel, 2 Button Screwed Cover Plate Kit, is suitable for Wired Rako WCM-020 Keypad Modules only.
Keypads are sold available separately
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
The Rako RLF-020, Black Nickel, 2 button Screwless Cover Plate Kit, is suitable for Wireless Rako RNC-020 and RCM-020 Keypad Modules only.
Keypads are sold available separately
The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The RAKO WK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wired commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cutout is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The Rako RMS-800 switching module can control up to 800 watts of mains non dimmable lighting loads. The unit can also be used for exterior lighting control applications, with the use of a weatherproof IP rated enclosure. The robust microprocessor design combines reliable switching with dynamic safety features such as auto-resetting over current and voltage surge protection. The RMS-800 switch module can be controlled from any Rako transmitter such as RCP/RCM wallplates, RAH hand helds, MB1 timeclocks and forms the foundation of any Rako scene-set system
The RCM070 push button control module comes pre-configured for selecting 4 scenes, off and master raise & lower. The wall plate controllers are designed to be mounted anywhere, be it flush mounting to UK back-boxes or simply surface mounted to any flat surface using the pattress provided. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement
The Rako RCM-020 Wireless keypad module is compatible with the RLF and RVF series coverplates. It is a wireless 2 button control module that arrives pre configured for a scene 1 on, and off option. As the unit is wireless it can be mounted anywhere on a rigid surface you will need the coverplate kit for mounting. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
Rako WP-EOS-6 in Polished Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The RAKO RAK8-MB is a 8 Channel modular dimming rack motherboard. It has 8 individual channel “slots” that allow complete flexibility of controlled loads when fitted with either of the WMT-400, WDA-600, WMS600 or WM-CUB control cards (these are an additional purchase) The RAK8 unit is stackable with other RAK8 units. It requires a RAK-LINK for wired systems or RX-LINK for wireless controlled systems.