Product Description
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
£193.20 (incl. VAT)
£32.40 (Inc. VAT)
£27.00 (Exc. VAT)
In Stock
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
Rako WP-EOS-6 in Polished Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.
Rako WP-EOS-6 in Satin Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.
The RAKO RAK8-MB is a 8 Channel modular dimming rack motherboard. It has 8 individual channel “slots” that allow complete flexibility of controlled loads when fitted with either of the WMT-400, WDA-600, WMS600 or WM-CUB control cards (these are an additional purchase) The RAK8 unit is stackable with other RAK8 units. It requires a RAK-LINK for wired systems or RX-LINK for wireless controlled systems.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The RAKO RK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wireless commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cut out is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako RACUB is a compact dual relay RF switching module. Ideal for integrating motorised curtains, blinds and projector screens with the lighting control system. Controlled from any Rako Rakom RF device, for example the RPS030 /060 or RCM030 / 060 three or six button RF wall plates.
The Rako RCM-020 Wireless keypad module is compatible with the RLF and RVF series coverplates. It is a wireless 2 button control module that arrives pre configured for a scene 1 on, and off option. As the unit is wireless it can be mounted anywhere on a rigid surface you will need the coverplate kit for mounting. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
The RNC push button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
Dear Customer, We will be closed from 23rd April 2024 until 24th April 2024. There will be no goods dispatched during this period. Please accept my apologies for any inconvenience this causes. Dismiss