Product Description
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
£177.60 (incl. VAT)
£32.40 (Inc. VAT)
£27.00 (Exc. VAT)
In Stock
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The RCM100 push button control module comes pre-configured for selecting 7 scenes, off and master raise & lower. The wall plate controllers are designed to be mounted anywhere, be it flush mounting to UK back-boxes or simply surface mounted to any flat surface using the pattress provided. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
The new Rako Modular range controller pads, RK-MOD-xx and WK-MOD-xxx require a Modular range Cover Plate to complete the installation. The Rako Modular range Cover Plates are available in seven heritage finishes.
The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
The Rako RCM-020 Wireless keypad module is compatible with the RLF and RVF series coverplates. It is a wireless 2 button control module that arrives pre configured for a scene 1 on, and off option. As the unit is wireless it can be mounted anywhere on a rigid surface you will need the coverplate kit for mounting. It is also suitable for all switch accessory plates that use a 50x50mm grid and cover plate arrangement.
The RAK-LINK provides an isolated link between the RAK4 dimmer units and wired RAKOM products. The unit also includes a heavy duty 15v dc power supply for the RAKOM network. Connection for the CAT5 is by 8 way punch down terminals. This allows for a daisy chain configuration of the RAKOM wired network. Where a ‘star’ or ‘home-run’ configurations are required the use of the RAK-STAR unit is needed. Three RJ11 programming sockets within the unit allows system programming using the RASOFT software suite and connection of other RAKOM accessories such as the WA-BRIDGE interface.
The RAKO RK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wireless commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cut out is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako RMR-VF is an interface unit to convert volt-free contact signals into Rako wireless RAKOM messages. This unit creates an interface between volt-free contact or DC logic inputs and Rako RF based receivers. The unit accepts up to 10 contact closures which can be mapped using RASOFT Pro to mimic keypad presses.
The Rako WMT-400 is a pluggable trailing edge dimmer module to be used with the RAK8-MB. The Rako WMT-400 unit is plugged directly into one of the slots on the RAK8- MB.
The WMT-400 can be used in combination with any of the other modules compatible with the RAK8 allowing for greater flexibility during both specification and installation. Trailing edge dimming technology gives smooth quiet dimming of electronic transformer fed loads and maximises dimming performance of most GU10 and other LED fittings.
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
The RNC wireless push button wall plate controller with 4 scenes, off and master raise and lower buttons. Customisable and programmable via NFC (Near Field Communication).
The RNC-100, 10 button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.