Product Description
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
£175.20 (incl. VAT)
£32.40 (Inc. VAT)
£27.00 (Exc. VAT)
In Stock
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The Rako WVF-100, White Metal, 10 Button Screwed Flat Cover Plate Kit, is suitable for Wired Rako WCM-100 Keypad Modules only.
Keypads are sold available separately
The Rako RMT-500 is a trailing edge 500W ceiling-mount dimmer.The RMT500 uses trailing edge dimming technology to maximise the performance of most GU10 dimmable LED down-lights (refer to Rako Controls for compatibility and maximum loadings). The RMT500 is also the recommended dimmer for GU10 tungsten lamps due to its in-built short circuit protection, necessary with this style of lamps.
The Rako RLED75CV1 is An in-line RF 75w single channel, constant voltage dimming LED driver. The compact single channel 75W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED fittings. Controlled from any Rako Rakom device, e.g. RCP/RCM wall plates or Bridge interface units.
The RNC wireless push button wall plate controller with 4 scenes, off and master raise and lower buttons. Customisable and programmable via NFC (Near Field Communication).
The RNC-100, 10 button control module is programmable via Rako’s patented NFC (Near Field Communication) technology allowing each of the buttons to trigger a single or multiple commands. Each input is fully customisable, can be addressed to separate Rako Rooms or Channels and activate on press, or release which gives a ‘Press and Hold’ function.
The Rako WM-CUB is a Twin Relay curtain and blind control card which forms part of the new RAK8 modular system. The new RAK8 modular system allows you to add individual control cards to your RAK8-MB (modular board) with complete flexibility to build a bespoke system to meet your requirements. The WM-CUB is used for implementation of control, for motorised curtains, screens and blinds. Delivering an open, close and stop functionality.
CyberSelect now offer a Rako Pre-Programming Service for Rako Lighting Control modules purchased from CyberSelect.
We have an experienced installation team, who complete installs every week. These installations range from larger complex lighting systems, integrated lighting within a Smart Home, to small and simple Rako Lighting Control both Wired Systems and Wireless Systems working seamlessly together. They can assist with pre-programming of your modules for your Rako Lighting Control and Home Automation System.
The Rako RLED150CV1 wireless Single channel 150w Dimmer is a compact single channel 150W constant voltage LED dimmer with in-built RF receiver and Rako processor for control of single channel constant voltage LED tape light.
The Rako RLED150CV1 is programmed using either a RCM/RCP RF wallplate or the RASOFT PC software suite, the unit stores the house, room and channel address plus 16 preset scene levels in non volatile memory. The RLED150CV1 dimmer can be controlled from any Rako transmitter such as RCM/RCP wallplates, RAH hand helds and Bridge modules and forms the foundation of any Rako scene-set system. For more information on dimming LEDs refer to Rako’s application sheet ‘Controlling LED Lighting With Rako Dimmers and Modules’.
The RLED30-CV4 is a wireless 4 channel, 30w/channel (Red, Green, Blue & White) constant voltage colour controller, For larger systems the Rako RLED30 Slave would be used to extend or amplify your desired circuit.
A compact 4 channel 30W per channel, constant voltage LED dimmer with in-built RF receiver and Rako processor for control of 4 channel constant voltage LED fittings.
A compact 800VA RF dimmer for 1-10V, DALI and DSI controllable loads. Connected in-line before the first lighting fitting the RMS800 enables switching of up to 800VA of 0-10V, DALI and DSI controllable loads such as LED drivers and dimmable fluorescent ballasts. Controlled from any Rako Rakom RF device, for example the RCP/RCM push button RF wall-plates.
The Rako WLED75CV1 is a wired 75W constant voltage LED dimmer designed for use with single channel constant voltage LED fittings and single channel LED tape light. Maximum wattage of 75W for 12V d.c. fittings or 150w for 24V d.c. fittings. Requires a suitable external d.c. power supply (normally the power supply that would be supplied with the fitting for a non-dimming application).
Controlled from any Rako Wired device, e.g. WCM, WAPIR or from wireless devices via a WA/WTC-Bridge or WRB100.
The RAKO RK-PIR is a Ceiling mounted occupancy sensor with built in smart, time conditional features and light sensing.
The WK-PIR motion detector allows Rako wireless commands to be transmitted automatically when sensing movement. Providing a highly sensitive motion detection over a large area.
Presented in a discrete and aesthetically improved design, a 48mm diameter ceiling cut out is required. For mounting, it is held in place with internal metal clips, no fixing screws are required.
The Rako Rak-Star is a wired connection unit allowing multiple CAT5 ‘star’ or ‘home run’ cables to be connected to the Rako wired network, generally for when the installer prefers to wire control panels in this fashion. The RAKStar also allows each ‘leg’ to be isolated making cabling fault identification easier. No additional power supply is required, the unit is fed from the RAK-LINK units via either the RJ11 sockets or the CAT5 network.
Rako WP-EOS-6 in Satin Chrome 6-Button wired EOS wall plate controller connects to the RAKOM wired CAT5 network and is preconfigured with 3 scenes, off and master raise and lower buttons.